Perko 0584S Manual do Utilizador descarregar pdf

Swivel Inlet Check Valves for EPA Compliant Fuel Systems

Perko Series 0584S0A for Aluminum Tanks

INSTALLATION INSTRUCTIONS

PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING

These valves are for use on fuel tanks to comply with the CARB and EPA standards and meet the

requirements of U.S.C.G. Safety Standards (July 31, 2011) for 40 CFR Parts 9, 60, 80 et al. (Control of

Diurnal Emissions From Nonroad Spark-Ignition Engines and Equipment). Note: Inspect valve fitting

and snap ring annually for corrosion, replace if necessary.

Series 0584S0A Inlet Check Valves (ICV), (0°, 45° & 90°)

1. These valves are designed to mount on aluminum surfaces.

2. Select your mounting location. Drill 2-1/4” diameter hole for valve receiver.

3. Weld the receiver to the tank

4. Slide the valve into receiver and orient hose barb in the direction of the vent line. Attach

locking snap ring to hold valve in the receiver.

5. Attach 1-1/2” fill hose onto hose barb and tighten using hose clamps in accordance

with ABYC Fuel System Vent Hose Clamping Standards (H24 Table 3).

PERKO, INC.

16490 N.W. 13th Avenue

Miami, FL 33169-5707

www.perko.com

11/12

0584INS3

*The above referenced standards can be obtained from:

(1). American Boat & Yacht Council, Inc. (2) U.S. Coast Guard (3). E.P.A.

613 Third Street, Suite 10 Washington, D.C. 20593 401 “M” Street S.W.

Annapolis, MD 21403 (or your local C.G. office) Washington, D.C. 20460

CARB

&

45°

0°

90°

Fig. 0584S0000A

Fig. 0584S4500A

Fig. 0584S9000A

Valve

Snap Ring

Receiver

Swivel Inlet Check Valves for EPA Compliant Fuel Systems

Perko Series 0584S0A for Aluminum Tanks

INSTALLATION INSTRUCTIONS

PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING

These valves are for use on fuel tanks to comply with the CARB and EPA standards and meet the

requirements of U.S.C.G. Safety Standards (July 31, 2011) for 40 CFR Parts 9, 60, 80 et al. (Control of

Diurnal Emissions From Nonroad Spark-Ignition Engines and Equipment). Note: Inspect valve fitting

and snap ring annually for corrosion, replace if necessary.

Series 0584S0A Inlet Check Valves (ICV), (0°, 45° & 90°)

1. These valves are designed to mount on aluminum surfaces.

2. Select your mounting location. Drill 2-1/4” diameter hole for valve receiver.

3. Weld the receiver to the tank

4. Slide the valve into receiver and orient hose barb in the direction of the vent line. Attach

locking snap ring to hold valve in the receiver.

5. Attach 1-1/2” fill hose onto hose barb and tighten using hose clamps in accordance

with ABYC Fuel System Vent Hose Clamping Standards (H24 Table 3).

PERKO, INC.

16490 N.W. 13th Avenue

Miami, FL 33169-5707

www.perko.com

11/12

0584INS3

*The above referenced standards can be obtained from:

(1). American Boat & Yacht Council, Inc. (2) U.S. Coast Guard (3). E.P.A.

613 Third Street, Suite 10 Washington, D.C. 20593 401 “M” Street S.W.

Annapolis, MD 21403 (or your local C.G. office) Washington, D.C. 20460

CARB

&

45°

0°

90°

Fig. 0584S0000A

Fig. 0584S4500A

Fig. 0584S9000A

Valve

Snap Ring

Receiver

1 2

Resumo do Conteúdo

Página 1

Swivel Inlet Check Valves for EPA Compliant Fuel SystemsPerko Series 0584S0A for Aluminum TanksINSTALLATION INSTRUCTIONSPLEASE READ ALL INSTRUCTIONS B

Swivel Inlet Check ValvesFor EPA Compliant Fuel SystemsPerko Series 0584S0P for use on Plastic TanksINSTALLATION INSTRUCTIONSPLEASE READ ALL INSTRUCTI

Comentários a estes Manuais

Sem comentários